Apr 282018
 

So, a few weeks ago I installed a new battery charger, and tweaked it so that the solar did most of the leg work during the day, and the charger kept the batteries topped up at night.

I also discussed the addition of a new industrial PC to perform routing and system monitoring functions… which was to run Gentoo Linux/musl. For now, that little PC is still running Debian Stretch, but for 45 days, it was rock solid. The addition of this box, and taking on the role of router to the management network meant I could finally achieve one of my long-term goals for the project: decommissioning the old server.

The old server is still set up with all my data and software… but now the back-up cron job calls /sbin/poweroff when it’s done, and the BIOS is set to wake the machine up in the evening ready to receive a back-up late at night.

In its place, a virtual machine clone of the box, handles my email and all the old functions of that server. This was all done just prior to my father and I leaving for a 3 week holiday in the Snowy Mountains.

I did have a couple of hiccups with Ceph OSDs crashing … but basically re-starting the daemons (done remotely whilst travelling through Cowra) got everything back up. A bit of placement group cleaning, and everything was back online again. I had another similar hiccup coming out of Maitland, but once again, re-starting the daemons fixed it. No idea why it crashed, that’s something I’ll have to investigate.

Other than that, the cluster itself has run well.

One thing that did momentarily kill the industrial PC though: I wandered down to the rack with a small bus-powered 2.5″ HDD with the intent of re-starting my Gentoo builds. This HDD had the same content as the 3.5″ HDD I had plugged in before. I figured being bus powered, I would not be dependent on mains, and it could just chug away to its heart’s content.

No such luck, the moment I plugged that drive in, the little machine took great umbrage to the spinning rust now vacuuming the electrons away from its core functions, and shut down abruptly. I’ve now brought my 3.5″ drive and dock down, plugged that into the wall, and have my builds resuming. If power goes off, hopefully the machine either handles the loss of swap gracefully. If it does crash, the watchdog will take care of it.

Thus, I have the little TS-7670 first attempting a build of gcc, to see how we go. Finger’s crossed our power should remain up. There was at least one outage in the time we were away, but hopefully we should get though this next build!

The next step I think should be to add some control of the mains charger to allow the batteries to be boosted to full charge overnight. The thinking is a simple diode-OR arrangement. Many comparators such as the LM393 have an open-collector output, which gives us this for free.

The theory is this.

The battery bank powers a simple circuit which runs of a 5V regulator. That regulator powers a dual comparator IC and provides a reference voltage. The comparator draws bugger all power, so I’m happy to use a linear PSU here. It’s mainly there as a voltage reference.

Precision isn’t really the aim here, so adjustable pots will make life easier.

The voltages from the battery bank and the solar panel are fed through voltage dividers to bring the voltages down to below 5V, then those voltages are individually fed into separate pots that control the hysteresis. I can adjust all points of the system.

The idea is that should the batteries get too low, or the sun go down, one or the other (or both) comparators will go low and pull down on R2. If the batteries are high and the sun is up, nothing pulls on R2 so the REMOTE+ pin on the HEP-600C-12 is allowed to float to +5V, turning off the mains charger.

The advantage of this is there’s no programming of a microcontroller, it’s just analogue electronics. The LM393s are pretty hardy things, the datasheet says they’ll run at 36V and can accept a maximum voltage of VCC-1.5V; so if I run at 5V, 3.5V is my recommended maximum. The adjustment pots should let me set a threshold voltage that avoids going above this.

I mainly need 5V for the HEP-600C-12, and for providing that stable known voltage reference. The LM78C05 should be fine for this.

Once I’ve done that, I should be able to wind that charger back up to its factory setting of 14.4V, which will mean that overnight the batteries will be charged back to full charge.