For 6LoWHAM, it could work that we just use the link-local address space to directly communicate between stations and leave it at that.
If I want to send a message to
VK4BWI-5 from my station
VK4MSL-9, I could just fire off a packet to
fe80::6894:49ff:feae:7318 directed to my 6LoWHAM interface and be done with it. This then requires one of two things:
VK4BWI-5can directly communicate with me
- that the intermediate stations know to forward my message on to that station
(1) is easy enough. (2) raises the question of “what is local”?
Supposing that this protocol took off, and suddenly the WIA decides to earmark special frequencies on a few bands for 6LoWHAM, with a fairly complete network stretching up the eastern seaboard of Australia. If my station sends a router solicitation from my home QTH in Brisbane, does someone in Melbourne really care to hear it? I’d wager this is a recipe for a very clogged packet network!
In Thread, the “link local” scope only gets you as far as the nodes that can directly hear you. It does mean that protocols like mDNS, which rely on the “link-local” multicast scope aren’t going to reach all nodes, but it also means that far flung nodes don’t need to listen to all the low-level chatter. For communications between nodes, an “on-mesh” prefix is used, and for mesh-wide multicast, a “realm-local” prefix of
ff03::/64 is defined.
In truth, it’s highly unlikely that we’d have “one” single network. More likely it’ll be a mesh of interconnected networks with trunk links going via some other band (or perhaps VPNs over the Internet). For that to work, we can’t rely on just link-local networking, we actually need a routable network address for the mesh.
The Thread “mesh local” prefix is actually defined by the network’s extended IEEE-802.15.4 PAN ID, which is a 64-bit number that you define when setting up the network. Thread simply takes the most significant 40 bits of this, slaps
fd in front and pads it out with zeros to 64-bits. The PAN ID
0x0123456789abcdef forms the subnet
fd01:2345:6789::/64. This can be seen in the OpenThread sources.
This wastes 16-bits of address space normally reserved for the ULA subnet ID and throws away 24-bits of the PAN ID. For our network, we don’t need 16-bits worth of subnets, we just need one. We also don’t have a PAN ID in AX.25.
The thinking is, we’ll use a “group” address. This will be a regular AX.25 SSID, which will translate to a MAC which has the group bit set. (Exactly how I’ll differentiate between a station SSID and a group SSID I’m not sure. Probably will look at the destination IP, if it’s multicast then the group bit gets set.)
Supposing we were to use this for the International Rally of Queensland (an event which is now defunct), we might create a 6LoWHAM network with a group address of “IROQ19”. The MAC address used for group-wide communications would be
We can derive a prefix from this MAC address. A ULA normally consists of a 7-bit ULA prefix, a 1-bit “global/local” bit, a 40-bit global ID, and a 16-bit subnet ID.
The ULA prefix is
fc::/7. The global/local bit is always set to 1 (local) because no one has come up with a way that ULAs can be globally administered. 40 bits is a bit tight, we could truncate our MAC to 40 bits and ignore the subnet ID like Thread do, that gives us a subnet of
The last 3 bits of the SSID though, are like a subnet ID. So if we move those 3 bits to set the last 3 bits of the prefix, we can make some use of that subnet ID, but still waste 13 bits with zeros.
Alternatively, we can consider the global ID and subnet ID to be one 56-bit field. We effectively shrink the subnet ID to 3 bits. That gives us a 53-bit global ID, which now fits the remaining 45-bits of our MAC and leaves us with 8 bits left over.
We can discard the lowest two bits in the first byte of the MAC as those (the group and local bits) will be the same for all groups, so that gives us another two bits. 10 bits isn’t a lot, but it’s enough to encode “AR” (amateur radio) in ITA-2, thus giving us a recognisable subnet mask for all 6LoWHAM networks. We wind up with the following:
┌─ULA─┐L┌──"AR"──┐┌───────────── Network Address ──────────────┐ 1111110100010010100000000000000111001101111001011010100111111000 └──┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┼───┤ f d 1 2 : 8 0 0 1 : c d e 5 : a 9 f 8 /64
This actually has me thinking whether the call-sign part of the SSID should be right-padded out to make the network address consistent. Maybe my SSID to MAC algorithm could do with a tweak there as it may make routing easier as it’ll put all those zeros to the right.
In Thread, the mesh-local prefix isn’t route-able beyond the mesh, there’s a separate prefix handed out by border routers for that. In our case, I don’t think there’s any point in complicating matters by having more than one route-able prefix for a mesh. If a station participates in two networks that share a frequency, then sure, that node may have an address on each network, but each network should share a common identity.
Thus in the contrived example of having a large network along the coastline: it’d be an “inter-network” of smaller meshes, linked together via router nodes which know how to hop between them. Those routes may be via point-to-point microwave links, HF, Internet tunnels, etc.
The subnets used for these other networks may be assigned a “context identifier” which is 4-bits. I’ll have to figure out if there’s a sane way to do that on a given network. Most 802.15.4 networks have a “PAN co-ordinator” which could be looking after that. Thread networks elect a “leader” node.
Given the small number of identifiers, and the low probability of this being used, this should be manually administered. Even without a context ID being assigned, one can still route between the subnets, just that the full IPv6 address needs to be given for the foreign node, so you incur a 16-byte penalty doing so. Thus the context IDs will probably be handed out for “popular routes”, with the mesh prefix being “context 0”.
I haven’t yet given thought to how this “context” would be disseminated over the mesh or kept updated. That is a can of worms for another day.